SIMPLEX Fire Detection And Alarm System

TrueAlarm sensor bases contain integral addressable electronics that constantly monitor the status of the detachable photoelectric or heat sensors. Each sensor’s output is digitized and transmitted to the system fire alarm control panel every four seconds.Since TrueAlarm sensors use the same base, different sensor types can be easily interchanged to meet specific location requirements. This feature also allows intentional sensor substitution during building construction. When conditions are temporarily dusty, instead of covering the smoke sensors (causing them to be disabled), heat sensors may be installed without reprogramming the control panel. Although the control panel will indicate an incorrect sensor type, the heat sensor will operate at a default sensitivity providing heat detection for building protection at that location.Digital Communication of Analog Sensing. TrueAlarm analog sensors provide an analog measurement digitally communicated to the host control panel using Simplex addressable communications. At the control panel, the data is analyzed and an average value is determined and stored. An alarm or other abnormal condition is determined by comparing the sensor’s present value against its average value and time.Intelligent Data Evaluation. Monitoring each sensor’s average value provides a continuously shifting reference point. This software filtering process compensates for environmental factors (dust, dirt, etc.) and component aging, providing an accurate reference for evaluating new activity. With this filtering, there is a significant reduction in the probability of false or nuisance alarms caused by shifts in sensitivity, either up or down.Control Panel Selection. Peak activity per sensor is stored to assist in evaluating specific locations. The alarm set point for each TrueAlarm sensor is determined at the host control panel, selectable as more or less sensitive as the individual application requires.Timed/Multi-Stage Selection. Sensor alarm set points can be programmed for timed automatic sensitivity selection (such as more sensitive at night, less sensitive during day). Control panel programming can also provide multi-stage operation per sensor. For example, a 0.2% level may cause a warning to prompt investigation while a 2.5% level may initiate an alarm.Sensor Alarm and Trouble LED Indication. Each sensor base’s LED pulses to indicate communications with the panel. If the control panel determines a sensor is in alarm, or is dirty or has some other type of trouble, the details are annunciated at the control panel and that sensor base’s LED will be turned on steadily. During a system alarm, the control panel will control the LEDs such that an LED indicating a trouble will return to pulsing to help identify the alarmed sensors.

4004R Suppression Releasing Panel for Automatic Extinguishing, Deluge and Preaction Sprinkler Control.Dedicated for Suppression Release. 4004R Suppression Release Panels provide conventional fire alarm control circuits and are equipped with the features required for a wide variety of single or dual hazard suppression release applications. Capabilities include automatic extinguishing agent release and deluge and preaction sprinkler control.

4007ES Series Fire Detection and Control Panelsprovide extensive installation, operator, and service features with point and module capacities suitable for a wide range of system applications. Panels can be configured for stand- alone or networked fire control operation. The convenient and intuitive color touchscreen provides easy access for typical system response actions and for detailed system review or configuration updates with password control to limit user access.IDNet+ addressable initiation communications and IDNAC addressable notification communications are standard features. (Refer to data sheet S4007-0001 for 4007ES panels providing conventional notification.)FeaturesFlexible standard combination of addressable initiation and addressable notification4.3” (109 mm) Diagonal color touchscreen display: Convenient and intuitive user interface provides detailedsystem status and individual point information Supports dual language selection, including unicodecharacter languages A custom background display appears when operation isnormal (see page 7 for details)Includes a 3 A IDNAC SLC (signaling line circuit) output power supply that provides enhanced power delivery to addressable notification appliances: A constant 29 VDC source voltage is maintained duringalarm, even during battery operation, allowing strobes to operate at higher voltage with lower current and ensuring a consistent current draw and voltage drop margin under both primary power and secondary battery standby Efficiencies include lower strobe currents, wiring distances up to 2 to 3 times farther than with conventional notification, support for more appliances per IDNAC SLC, and smaller gauge wiring. This provides installation and maintenance savings. with high assurance that appliances will operate as normal during worst case alarm conditions IDNAC SLCs are compatible with both TrueAlert ES and TrueAlert addressable notification appliances, and remote 4009 IDNAC Repeaters to extend power and wiring distance even farther and provide for up to 127 addressable notification appliances Power supply provides battery backup charging of up to 33 Ah; up to 18 Ah for cabinet mounted batteries and up to 33 Ah batteries for mounting in close-nippled remote battery cabinetElectrically isolated IDNet+ addressable initiating device SLC: Provides built-in short circuit isolation for monitoringand control of TrueAlarm analog sensors and IDNet communications monitoring and control devices; for use with either shielded or unshielded, twisted or untwisted single pair wiring; outputs are Class A or Class B Standard panel SLC provides up to 100 addressable points; optional additional loop expansion modules provide an additional isolated loop with short circuit isolation for the IDNet+ channel; each loop expansion module also provides an additional 75 addressable points to the IDNet+ channel capacity for a total of up to 250 addressable pointsSoftware Feature Summary: Current and previous panel configuration are both maintained in on-board memory to allow easy selection of desired revision An internal Ethernet service port is available for service computer connections to perform configuration updates, downloads and uploads; report downloads, and system software updates Internal USB interface allows a memory stick/thumb drive to store job revisions, update revised jobs and panel software, and save detailed system reports from the panel4007ES Fire Control PanelsFire Detection and Control with Addressable Initiation and Addressable Notification4007ES Panel Front ViewOptional modules and connections include: Fire Alarm Network Interface for Peer-to-Peer fire alarm network communications, supports either Class B or Class X operation Point or Event DACT assembly that is compatible with IP Communicators Up to two additional IDNet+ addressable device output loop connections with 75 additional point capacity each Front mounted 48 LED annunciator with custom label inserts. Dual Class A IDNAC Isolator (DCAI) Remote LED annunciator support via RUI (remote unitinterface) communications port for use with unshielded,twisted pair wiring (UTP) Eight Point Zone/Relay Modules individually selectableas IDC or relay rated 2 A @ 30 VDC (resistive) Alarm relays and auxiliary relays Dual RS-232 ports (for printer, PC annunciator or thirdparty interface) TrueInsight Remote Gateway City connections, with or without disconnect switch 4003EC V oice Control Panels 4009 Series IDNAC Repeaters Battery brackets for seismic area protection (see page 2) General Mechanical: Compact red or platinum cabinet for convenient surface orsemi-flush mounting; rated NEMA 1 and IP304007ES Listings reference: UL 864 - Control Units, System (UOJZ); Control Unit Accessories, System, Fire Alarm (UOXX); ; Control Units, Releasing Device Service (SYZV) UL 2017 - Emergency Alarm System Control Units (CO detection), (FSZI) ULC-S559 - Central Station Fire Alarm System Units (DAYRC) ULC-S527 - Control Units, System, Fire Alarm (UOJZC); Control Unit Accessories, System, Fire Alarm (UOXXC); Control Units, Releasing Device Service (SYZVC)* This product has been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. See CSFM Listing 7165-0026:0378 for allowable values and/or conditions concerning material presented in this document. NYC Fire Dept COA #6191A. Additional listings may be applicable; contact your local Simplex product supplier for the latest status. Listings and approvals under Simplex Time Recorder Co. are the property of Tyco Fire Protection Products.Alarm Kebakaran

The Simplex 4010ES is a highly flexible and powerful 250 to 1,000-point addressable system for small to mid-sized facilities. Unlike many systems of this size, points can be used for detectors, modules or manual stations as needed to help meet the requirements of each building. The 4010ES includes labour-saving features such as device-level ground fault isolation and almost dirty smoke sensor status reports that help reduce installation time for electrical contractors and allows for proactive maintenance to be scheduled at one-time to help eliminate unwanted nuisance alarms.4010ES panels are networkable and can be connected to other Simplex panels and TrueSite Workstation command centres. 4010ES panels are also compatible with TrueAlert ES addressable notification appliances and their revolutionary self-test capability. See pages 34 and 35 for more information on ground breaking TrueAlert ES technology.Features and BenefitsDesigned for small to medium building applications2GB of integrated, supervised storage for programming and system configuration information4120 network compatibleUp to 1000 points with multiple isolated loopsCompatible with TrueAlarm sensorsIDNet analog addressable devicesLCD remote annunciatorRemote 24 point I/OAvailable DACT for supervising station communicationsUL/FM listed for suppression releaseCertified for Seismic ApplicationsSafeLINC fire panel internet interfaceBACnet third party interface4003EC voice control panel compatibleCompatible with TrueAlert ES addressable notification appliances and their revolutionary self-test capability.

The Simplex 4100ES is based on a modular architecture allowing system designers to custom configure each panel and build a cost-effective system that meets project specifications and capacity requirements. The future proof design of Simplex systems reduces cost of ownership by allowingeasy expansion to accommodate changes throughout the life of the system.Simplex systems offer true integration including voice alarm/evacuation, agency listed non-alarm paging and background music, fire fighter telephones, emergency notification,Mass Notification Systems (MNS), smoke management and control, and available high level integration to third party systems utilising open protocols. Simplex systems also feature graphic workstations with remote PC and mobile client support as well as dual redundant configurations and addressable multi-candela audible/visual appliances including our unique Simplex TrueAlert text messaging display.Simplex UL listed textual notification appliance is designed to supplement standard notification appliances to improve life safety and addresses requirements for the hard of hearing/deaf community. Each display can also support custom non-alarm messages sent froma remote PC over a TCP/IP network which are overridden in an emergency condition such as a fire, security breach, or a hostile intruder.It’s important that a fire detection systemcan continue to be serviced, supported and upgraded throughout its life in order to protect the owners investment. Simplex systems are always engineered to provide a migration path to the latest technology and features available.Master Bay2GB of integrated, supervised storage for programming and system configuration informationSystem Power Supply (SPS) with on board IDNet channel, 3 NAC’s and Aux Power or Enhanced Power Supply (EPS) with dual loop IDNet 2 channel, 3 IDNAC SLC's for addressable notification andAux PowerCPU, Network Card, Media Cards, RS232Expansion BaysDual redundant CPU option for critical applicationsAudioFirefighter phonesRelays Cards, Zone Cards, IDNet CardsLED/Switch ModulesTCP/IP Physical BridgeSingle Fibre ModemsExpansion Power Supplies (XPS)TrueAlert Addressable Power SuppliesUL & FM approvedUniversal platform - small to large systemsNew processor with on board IP network capabilityIntegrated voice alarm and fire fighter phonesAgency listed non-alarm audio (paging and background music)Spoken WALKTESTVoice coding/message splicingCompatible with TrueAlert ES addressable notification appliances and their revolutionary self-test capability. See pages 34 and 35for more information on ground breaking TrueAlert ES technologySmoke management and controlHigh level networking, multiple topologies and connectivity optionsNetwork-wide synchronization of notification appliancesAvailable third party open protocol interfacesGraphic workstation with support for remote PC and mobile clients and dual redundant configurationsSafeLINC fire panel internet interface• UL Listed for Mass NotificationUL/FM listed for suppression release• Certified for Seismic ApplicationsMaster clock interface